5
5.0
May 1, 2021
05/21
by
Nick Orsi (AKNick)
data
eye 5
favorite 0
comment 0
Designed this tool to easily slip on a new tire to the Spot-On RC Flywheelz 4" wheel without damaging it. 15% infill 0.2 layering. Got the idea from using o-ring tools over the years.
Topics: stl, thingiverse, rc_tires, R/C Vehicles
6
6.0
May 1, 2021
05/21
by
Dennis Weser (Breadycorn)
data
eye 6
favorite 0
comment 0
A prototype for an airless tire I modelled after [Michelin Uptis](https://michelinmedia.com/michelin-uptis/) airless tire. I'm still very new to 3D modelling in Fusion 360 but I'm currently teaching myself how to make an RC car, this is the first step I took to learn this.
Topics: stl, Vehicles, rc_tires, wheel, thingiverse, tire
9
9.0
Apr 22, 2021
04/21
by
Tom Simpson (tslove28)
data
eye 9
favorite 0
comment 0
This is a smaller version of the universal rover wheel that you'll find in my creations list. I wanted to make the larger version support tracks and tires. The size makes it difficult (and expensive) to prototype with. I decided the mini universal rover wheel would allow me to design and test before I port it over to the larger wheel assembly. I've made a few alterations that should reduce some of the cost. This is earlier in the development cycle than I usually post things but it works as it...
Topics: Robotics, robotics, rc_tires, stl, thingiverse, tire
4
4.0
Mar 21, 2021
03/21
by
aaron helmick (AaronSc)
data
eye 4
favorite 0
comment 0
2.6" o.d 1.9" wheel 1.13" at widest point, 1.08 the inner edge
Topics: stl, rc_tires, rc, R/C Vehicles, thingiverse
7
7.0
Jan 20, 2021
01/21
by
Victor Zhang (victorzzt)
data
eye 7
favorite 0
comment 0
Reference : [A tutorial by Lars Christensen ] https://www.youtube.com/watch?v=PiCJWwoBUOE With the f3d file, parameters can be adjusted to change the tire and the thread. But some how I didn't do a good enough job that sometime when there's too few tire threads, the model break down. So advice to change the params a small step at a time. The example prints were with TPU (15mm/s, no retraction, 220C)
Topics: thingiverse, Toy & Game Accessories, tire, rc_tires, stl
4
4.0
Apr 13, 2021
04/21
by
aaron helmick (AaronSc)
data
eye 4
favorite 0
comment 0
1.5" i.d. 3.2"o.d. .75" wide not been made yet. I believe they would work good with ninjaflex. Wall thickness is .08", or approx. 2mm
Topics: thingiverse, tire, rc_tires, stl, R/C Vehicles
3
3.0
Jun 11, 2021
06/21
by
Martin Søgaard Schultz (Vibria)
data
eye 3
favorite 0
comment 0
Version 2 of my vintage tire - now threaded and with a higher profile
Topics: Threaded_tire, thingiverse, rc_tires, R/C Vehicles, stl
4
4.0
Jun 21, 2021
06/21
by
Hafiz Muhammad Umer (umer3d)
data
eye 4
favorite 0
comment 0
This is a 3D printable tire to be used with the yellow geared motors normally used with arduino robotics projects, Print the middle part in any normal filament (I used ABS) and the outer shell in TPU. To see my new designs, like my facebook page https://www.facebook.com/UmersLaboratory/ I can not receive tips here since PayPal doesn't work in my country. You can donate on patreon instead https://www.patreon.com/umer Thanks.
Topics: Robotics, diy, thingiverse, tire, arduino, stl, robot, rc_tires
4
4.0
Mar 21, 2021
03/21
by
aaron helmick (AaronSc)
data
eye 4
favorite 0
comment 0
5.35" O.D. tire 2.9" O.D. wheel 2." wide 12mm hex This is designed to convert a 1:14th scale ERTL tractor to Remote control. Minimum Thickness on the tire is.08"
Topics: stl, rc_tires, ERTL, RC, R/C Vehicles, thingiverse
4
4.0
Apr 1, 2021
04/21
by
Dionis Aphonich (Dionisnation)
data
eye 4
favorite 0
comment 0
And hello again, everyone.) I present to you the shock absorber system. It's for a wheel I used to make. There are plans to continue this project. I'm thinking of doing something like a post-apocalyptic car. I'll share the progress here. so sign up and keep an eye out for updates. Tire and other files: https://www.thingiverse.com/thing:4172286 https://www.thingiverse.com/thing:4159402
Topics: outroad, thingiverse, Shock_Absorber, wheel, DIY, rc_tires, stl
10
10.0
Apr 20, 2021
04/21
by
Alberto López (3l3m3nt)
data
eye 10
favorite 0
comment 0
As it seems that there is not any design or files for this I moved on and created the tires for my 3D LAB PRINT BF 109. 3 perimeters in the rims for more strength in the center holes.
Topics: thingiverse, stl, R/C Vehicles, 3dlabprint, rc tires, BF109
3
3.0
Apr 8, 2021
04/21
by
(PlasticyBits)
data
eye 3
favorite 0
comment 0
My attempt to design and print RC Plane Wheels and Tyres (or Tires) Tyre sizes are 2 and 3 inch outer diameter, in both a wide and narrow format Rims are also in wide and narrow format, with either 3mm or 4mm holes for axles. Tyres where done as my first attempt at printing in flexible TPU material, so these first ones in the picture are a bit rough, have changed the design since, which are the files uploaded. Rims are printed in PLA. These also came out rough as I printed on a very hot day in...
Topics: rc_tires, RC_wheels, stl, thingiverse, R/C Vehicles
8
8.0
Jan 20, 2021
01/21
by
Brad Bridges (CrackFox)
data
eye 8
favorite 0
comment 0
Pirelli Tire SVG to make vinyl decals for RC or model tires. Includes PZERO and Cinturato
Topics: thingiverse, OpenRC_F1, Signs & Logos, tire, rc_tires, pirelli, stl
3
3.0
Jun 6, 2021
06/21
by
Carlos Costa (SeekND)
data
eye 3
favorite 0
comment 0
Found these amazing tires made by Calisto: https://www.thingiverse.com/thing:2997226 But I didn't like that they were much wider, so I decided to chop them up a bit as to be used like a regular tire. I'm printing these with 0 infil in TPU, and add a bit more walls to it (0.5-0.7), so it acts like a rubber tire (slightly harder so you won't need the foam inside).
Topics: orlandoo_hunter, Orlandoo, thingiverse, Vehicles, stl, tires, tire, rc_tires
5
5.0
Jan 9, 2021
01/21
by
shawn gallagher (1337gallagher)
data
eye 5
favorite 0
comment 0
remix of Team panic's larger silicone molds for combat robots. used with 100% silicone with acetic cure. mix 4-5 drops of glycerine and 2-3 drops acrylic paint then apply directly to pla molds. let cure overnight and unmold. I find it helpful to use a popsicle stick to apply the silicone to both surfaces of the mold then twist as I gently mate the two halves. Overflow is good and is the reason gloves are reccommended. remixed from Antweight (150g) combat robot silicone wheels by Team_Panic...
Topics: thingiverse, stl, antweight, RC_Car, rc_tires, 150g, Robotics, wheels
4
4.0
Jan 16, 2021
01/21
by
V0 XeL (V0XeL)
data
eye 4
favorite 0
comment 0
Tires for RC cars, compatible with 3D Sets [3D-printed RC cars](https://www.3dsets.com/). Print using TPU. Mirror the model to print full sets of four tires. Tires have 45mm inner diameter for a tight fit, and therefore can't be printed with semiflex filaments, as they won't fit over the rims. Ultra-flexible filament with low infill is recommended. These tires have a built-in support element that needs to be cut off with scissors after the print.
Topics: 3dsets, thingiverse, R/C Vehicles, rc_tires, stl, RC_Car
2
2.0
Aug 9, 2021
08/21
by
Lomi gald (Xhoho)
data
eye 2
favorite 0
comment 0
Follows and like are appreciated to let me know if i should do more models The Model was imported from Assetto Corsa and converted from fbx to stl with all details Full detail kranze cerberus 3 the model might not be perfect so modification might be needed The Print Has Not Been Tested Scale: You Choose Author: DWG Model: kranze cerberus 3 Remix: xhoho The model might need some modifying Feel free to comment and give feedback If you'd like a specific car just message me or comment and ill try...
Topics: tires, thingiverse, model, 3peace, 3D Printing, rc_tires, stl, wheels
6
6.0
Jan 16, 2021
01/21
by
V0 XeL (V0XeL)
data
eye 6
favorite 0
comment 0
Tires for RC cars, compatible with [3D Sets 3D-printed RC cars](https://www.3dsets.com/). Print using TPU. Mirror the model to print full sets of four tires. Tires have 45mm inner diameter for a tight fit, and therefore can't be printed with semiflex filaments, as they won't fit over the rims. Ultra-flexible filament with low infill is recommended. These tires have a built-in support element that needs to be cut off with scissors after the print.
Topics: 3dsets, thingiverse, R/C Vehicles, rc_tires, stl, RC_Car
4
4.0
Mar 15, 2021
03/21
by
vinny wilkerson (vinny11905)
data
eye 4
favorite 0
comment 0
Rear tires were dry rotted so I made new ones with tinkercad. printed with flexible filament.
Topics: tire, thingiverse, RC_Car, matchbox, Mechanical Toys, rc_tires, stl
9
9.0
Apr 28, 2021
04/21
by
Lucas West (ThreeDeePrint)
data
eye 9
favorite 0
comment 0
This project is a tire tread for emmett's gear bearing. It is a very tight fit and can be easily hammered in with a rubber mallet. This can be used for anyone who wants a wheel that has grip and can spin smoothly and freely. Find emmett's gear bearing here https://www.thingiverse.com/thing:53451
Topics: thingiverse, gear_bearing, Tire, stl, rc_tires, R/C Vehicles, RemixChallenge
3
3.0
Mar 19, 2021
03/21
by
Ed Oyo (Abu_Jayden)
data
eye 3
favorite 0
comment 0
I designed these tires to fit Mopf's awesome rims https://www.thingiverse.com/thing:3543760 for the Wltoys K989. I posted 2 versions, tiny tires K989 thin and tiny tires K989 thick. The thicker version has more cushion and traction. Print one tire first to test fit, you may need to scale up or down for optimal fit without glue. Additionally, these are directional tires so you may want to flip 2 of them before you print
Topics: rc_tires, R/C Vehicles, RC_Car, thingiverse, wltoys_k989, stl
4
4.0
Mar 21, 2021
03/21
by
aaron helmick (AaronSc)
data
eye 4
favorite 0
comment 0
For 1.9" wheel. 4.2" o.d 1.11" wide Like the other, it should be good to print in ninja flex.
Topics: stl, tire, rc_tires, RC, R/C Vehicles, Ninja_Flex, thingiverse
7
7.0
Jan 20, 2021
01/21
by
Steven Weathers (stevenweathers)
data
eye 7
favorite 0
comment 0
I joined the the following tire and wheel to make 1 stl for 3d printing as one piece, perfect for Gaslands or other miniatures games. Jeep Wheel https://www.thingiverse.com/thing:2056923 Tire https://www.thingiverse.com/thing:2119923
Topics: gaslands, tires, thingiverse, Toy & Game Accessories, offroad tire, rc_tires, stl
4
4.0
May 1, 2021
05/21
by
Dylan Gelinas (Signeddiamond)
data
eye 4
favorite 0
comment 0
As I make my way through my Eaglemoss subscription I realized that I wanted someplace to display the tires while I built the rest of the time machine. This print requires some 3 mm rod cut to size and an optional brushed stainless steel plate for the back (Because of course). This design was inspired by a in store tire display I saw at a local shop.
Topics: stl, Vehicles, delorean, Time_Machine_Delorean, rc_tires, Eaglemoss_Delorean, thingiverse
10
10.0
Apr 30, 2021
04/21
by
daniel sprehe (dsprehe89)
data
eye 10
favorite 0
comment 0
This is a remix of kallaspriit's "Spiked" RC car wheel. It is designed to fit a 12mm hex, but the solidworks (2013) source file is available if you wish to make is smaller or larger for your needs. I printed my rim at 25% infill with PLA and it held up decently well. I ran the car very hard over numerous jumps for 30 minutes straight in 15 degree weather today. I lost a couple of the spikes, but I feel that is because I was running it in very thin snow. I suspect it would work much...
Topics: stl, rims, RC_Car, rc_tires, rim, thingiverse, R/C Vehicles
3
3.0
Apr 5, 2021
04/21
by
zach hodges (Zachhodgesmtb05)
data
eye 3
favorite 0
comment 0
hi This is a tire mold that you can cast more grippy tires for the open RC f1 car. I noticed that with the normal tpu tires they just do not have enough grip to accelerate the car at any reasonable amount of time. So I tried wrapping rubber bands around the tires but that did not work because they would just slip off and I would have to rewrap the tires every 5 minutes and that got old really quick. then I tried to hot glue the bands on, they stayed on for a while but after a few minutes the...
Topics: thingiverse, R/C Vehicles, OpenRC_F1, tires, rc_tires, openrc, stl
6
6.0
Mar 16, 2021
03/21
by
Jeremiah Tinkham (dirtbiker00)
data
eye 6
favorite 0
comment 0
These are 1/10 scale tires I designed for my Traxxas Rustler VXL. They will work on any Traxxas car with 12mm hex hubs and 6mm drive shafts. Dimmensions: 6mm drive shaft 12mm hex 71 mm diameter (2.8 inches) 40 mm wide **The two files are mirrors of each other (one for each side of the car), so make sure to print at least one of each**
Topics: 12mm_hex, traxxas, stl, wheels, thingiverse, R/C Vehicles, rc_tires
9
9.0
Jan 12, 2021
01/21
by
Brais (Torretastop)
data
eye 9
favorite 0
comment 0
This is my first tire for a rc 1/10 rally car. Inside diameter: 52mm I hope you like it!!
Topics: R/C Vehicles, thingiverse, stl, sand, ground, tire, rc_tires, car
4
4.0
Mar 13, 2021
03/21
by
SANTIAGO TRAVEZ (SANTY1)
data
eye 4
favorite 0
comment 0
llanta de mini carros
Topics: thingiverse, RC_Car, tires, car, tire, Toys & Games, stl, rc_tires
4
4.0
Mar 25, 2021
03/21
by
(EremaStar)
data
eye 4
favorite 0
comment 0
For this https://ru.aliexpress.com/item/33060192011.html?spm=a2g0s.9042311.0.0.274233edV7q6bM
Topics: stl, R/C Vehicles, thingiverse, wheel, tire, RC_Car, rc_tires
3
3.0
Apr 1, 2021
04/21
by
Paul Nunes (biggsfx)
data
eye 3
favorite 0
comment 0
This is my version of a classic ribbed front tire for RC10 fits the classic style wheels. I added some spikes between the ribs to help support them when printing but I think they look pretty good too. A little bit of flex, I think they will be good for loose dirt and sand. Added a dirt rear tire prototype. Haven't printed yet.
Topics: RC_Car, thingiverse, team_associated, RC10, rc_tires, stl, Vehicles, rc_tire
10
10.0
Jan 18, 2021
01/21
by
Austin Brown (Crazymotoman03)
data
eye 10
favorite 0
comment 0
This is a modular tire system for any rc with a 12mm hex on it. the tires are all under 122mm most around 110mm in size and about 32mm width. I used the designs from these two creators. ChMiBr, and martimo. make sure to check out there AWESOME designs! and special thanks to them for letting me use and modify their designs. The rims should fit although they may be a little tight on the hex but they do fit once squeezed on. the outside of rims and inside of tire aren't a perfect fit so to fit...
Topics: Buggy, thingiverse, wheel, tire, R/C Vehicles, rc_tires, Airless_tire, stl
3
3.0
Jun 11, 2021
06/21
by
Christian Huber (ChrisPV)
data
eye 3
favorite 0
comment 0
These are 20mm,21mm and 22mm drift tires for MiniZ or any other 1:28 chassis, they are all 11mm wide, if you need them for slim rims just scale them down in your slicer. Print them in PLA with 100% infill, mount them at your car and then grind them until they have a nice flat surface. that for i stick sandpaper with some tape to a flat surface and hit the throttle. first i take 40 grid sandpaper, than 220 grid, and at last 1000 grid have fun drifting...
Topics: drift, thingiverse, rc_tires, tires, tire, R/C Vehicles, rc_drift, stl
3
3.0
Jan 18, 2022
01/22
by
Nick Bardo (Nick3dmaster)
data
eye 3
favorite 0
comment 0
This is a tire rack for a Traxxas F-150 Raptor or the Slash version of the Raptor. It is a very easy installation, though you will need a bit of glue. - Print the rack and the bed mounting bricks - Use a bit of glue (Hot glue will work) and attach the bricks in the grooves of the bed - Slide in the rack and use a piece of 1.75mm to pin it in if needed (You may want to use some string or wire to secure the tires in) Be sure to check out my trailer hitch for it as shown in the first pic -...
Topics: RC_Tire_Mount, RC_Car, thingiverse, R/C Vehicles, rc_tires, stl
11
11
Jan 11, 2021
01/21
by
M. Koper (Marcel_Thingyverse)
data
eye 11
favorite 0
comment 0
Storage your wheels and look great while doing it :P. Requires 4x M4 threaded rods, length is up to you depending on tire width. You might need some super glue for the end caps. Print 2x side panel, 8x end cap. Don't forget to mirror one side panel on the x axis in your slicer.
Topics: RC_wheels, R/C Vehicles, thingiverse, stl, RC_Car, rc_tires, wheels
5
5.0
Jan 9, 2021
01/21
by
Steve Martin (battleCat3000)
data
eye 5
favorite 0
comment 0
Just a simple tool for removing the knock offs on the wheels of the Redcat SixtyFour Lowrider
Topics: R/C Vehicles, thingiverse, stl, tire, RC_Car, rc_tires, wheel, Lowrider
3
3.0
Jan 19, 2022
01/22
by
David Jarboe (davidchuck)
data
eye 3
favorite 0
comment 0
I whipped these up thinking I could print some aggressive looking / performing wheels and tires for my WLToys 124018 buggy. I printed wheels in ABS, and tires in TPU. I printed the tires with only 2 layer lines and a single support down the middle of the tire, to maintain maximum flexibility. The tires deteriorate quickly this way, but they to look good and fit well. In the sand, grass, and snow these perform very very well... On asphalt it turns the buggy into an awesome drift car!!!
Topics: WLToys 124018, 85mm Tires, thingiverse, 124018, Buggy Tires, TPU RC Tires, R/C Vehicles, WLToys, RC...
8
8.0
Jan 15, 2021
01/21
by
John Wenzelburger (wenzej)
data
eye 8
favorite 0
comment 0
This is a tire tread for the "Remotely controlled - Arduino Self balancing robot" https://www.thingiverse.com/thing:2306541 It has to be printed with Flex filament to work. It will wrap around the wheel and make it wider so it fits very well. The stretch of the flex filament should overcome any printer miss calibration. It is not as grippy(sticky) as I would like on a smooth surface, it might slip. On any soft surface it should be fine. You might be better off with the bike innertube...
Topics: thingiverse, tire_tread, stl, tire, rc_tires, Self_Balancing_Robot, Robotics, robot
9
9.0
Jan 12, 2021
01/21
by
Martin Wulf (WerkstattleiterModding)
data
eye 9
favorite 0
comment 0
This is model rim. Size must be chosen by everyone. Is scalable
Topics: oz_racing, R/C Vehicles, thingiverse, rims, stl, rc_rims, rc_tires
2
2.0
Apr 19, 2022
04/22
by
Eben Kok (Baladop)
data
eye 2
favorite 0
comment 0
I love the design by dukedoks and just wanted some more ground clearance. So I made the original rims wider and designed bigger tires from scratch. The tires give about 15mm more clearance and really improves the traction. I still use a normal SG90 servo and the car is very responsive. The tires were printed with CCTree TPU with a 6% gyroid infill at 40mm and took 5 hours per tire. Another change is to use m3x45 bolts for the front wheels and to put an m3 nut at the end of it, I found that on...
Topics: thingiverse, rims, rc_tires, RC_Trucks, RC_Car, wheel, R/C Vehicles, stl
9
9.0
Apr 17, 2021
04/21
by
Vaclav Mica (Vasek_3Dmodel)
data
eye 9
favorite 0
comment 0
1.9 Beadlock for crawler
Topics: RC Tire, thingiverse, Crawler tire, stl, R/C Vehicles, 19_beadlock, rc_tires
6
6.0
Jan 3, 2021
01/21
by
Jonathan Charpentier (Dallasfj40)
data
eye 6
favorite 0
comment 0
Just something I drew up for myself, Fits 26mm wide wheels. Use 100% infill
Topics: R/C Vehicles, stl, rc_drift, drifting, thingiverse, drift, RC_Car, rc_tires
2
2.0
Apr 19, 2022
04/22
by
Paul Blythe (Build_Me_Something)
data
eye 2
favorite 0
comment 0
A tire press to help remove mounted RC drift car tires from the rims... Print in PLA or PETG with 0.2mm layers, a wall thickness of 1.35mm (3 walls), and a top/bottom depth of 1mm (5 layers). Sturdy enough to be used with a clamp for stubborn tires.
Topics: rc_drift, thingiverse, press, rc_drift_wheels, rc_tires, R/C Vehicles, stl
3
3.0
May 20, 2021
05/21
by
Denes Nagymathe (Denes)
data
eye 3
favorite 0
comment 0
My K989 had way too much grip on my carpet so i made this wheel to make it more fun. Print in PLA and start drifting! :)
Topics: WLtoys, R/C Vehicles, thingiverse, rc_tires, tire, stl, wheel, k989, RC_Car
3
3.0
Jan 19, 2022
01/22
by
David Jarboe (davidchuck)
data
eye 3
favorite 0
comment 0
I whipped these up thinking I could print some aggressive looking / performing wheels and tires for my WLToys 124018 buggy. I printed wheels in ABS, and tires in TPU. I printed the tires with only 2 layer lines and a single support down the middle of the tire, to maintain maximum flexibility. The tires deteriorate quickly this way, but they to look good and fit well. In the sand, grass, and snow these perform very very well... On asphalt it turns the buggy into an awesome drift car!!!
Topics: WLToys 124018, 85mm Tires, thingiverse, 124018, Buggy Tires, TPU RC Tires, R/C Vehicles, WLToys, RC...
11
11
Apr 30, 2021
04/21
by
jan cato myren (jan1cato)
data
eye 11
favorite 0
comment 0
front tyre/tire for my rc truck prosject
Topics: stl, truck, tires, tamiya, tyre, rc_tires, tyres, thingiverse, R/C Vehicles, tire
10
10.0
Apr 22, 2021
04/21
by
Brian Bray (Dakakeisalie)
data
eye 10
favorite 0
comment 0
This will work with AndyMark 8" pneumatic tires and probably most others too. This hub should fit any 200x50mm labeled tire. Print two and to assemble you will need Six (6) #4-40x1" bolts that should self tap into the plastic to keep the wheel together. For any kind of use I would highly recommend at least 3 more #10 bolts through the main bolt circle.
Topics: Robotics, rc_tires, thingiverse, wheel, stl, wheels, FIRST_FRC, frc_robotics, tire, frc
3
3.0
Jun 7, 2021
06/21
by
Dirk Wackenhut (DW1988)
data
eye 3
favorite 0
comment 0
I needed a Cover for my RC Tires. So I quick Draw one for my needs. It is for 4x Tires with 66mmx27mm The Print is working without Support! Look at the 2 Picture for Print Orientation
Topics: RC_Car, cover, thingiverse, stl, tires, 110, R/C Vehicles, rc_tires, box
4
4.0
Mar 15, 2021
03/21
by
Ludovic Martinelle (Cobactan)
data
eye 4
favorite 0
comment 0
Tires for Carduino and WlToys A959 to be printed in TPU.
Topics: WLtoys, thingiverse, tires, RC_Car, rc_tires, R/C Vehicles, stl, WLtoys_959
9
9.0
Mar 13, 2021
03/21
by
David Garner (Dgarner5005)
data
eye 9
favorite 0
comment 0
Made this for Thingaverse file 33160. http://www.thingiverse.com/thing:33160 The tire fits snug and the wheel allows for a press fit onto a servo spline. The Design allows for a spline screw to secure the wheel to the servo.
Topics: thingiverse, Servo_Mount, RC_Car, servo_horn, R/C Vehicles, stl, rc_tires
